Efficient solutions for your comfort

Search 

Call us

0758 716 716

ARTBuilding services

Solutions for every system in the building

Whether we are talking about a new project, a residential building, an office building, commercial or industrial premises, or an existing building, we are by your side to deliver and maintain the comfort you want, extend service life and improve the efficiency of sanitary, air conditioning, heating, ventilation and fire protection equipment and installations.

Equipment sales

Sales of heating, air conditioning, ventilation and water supply equipment

Air conditioning systems

  • Residential air conditioners
  • Multisplit systems
  • Commercial air conditioners: cassette, duct, ceiling and floor units
  • SKYAIR and VRV air conditioning systems
  • Cooling units, CHILLERS

Heating systems

  • Heat pumps
  • Condensing boilers
  • Electric boilers
  • Condensing boilers with outputs from 45 kW to 3000 kW
  • Expansion vessels
  • Small and large water heaters
  • Pressure regulators
  • Water softening stations

Ventilation and air handling systems

  • Air handling units
  • Heat recovery units
  • Household fans
  • Commercial fans
  • Air heaters
  • Industrial air purifiers
  • Air curtains
  • Patio heaters

Pumping systems

  • Well pumps
  • Pressure boosting and maintenance pumps
  • Booster sets with 1 to 5 pumps
  • Wastewater drainage systems
  • Fire fighting pump sets
  • Distribution and recirculation pumps
  • Expansion vessels
  • External frequency converters

Suppliers / Partners

  • Wilo
  • Frico
  • Reflex
  • Honeywell
  • Woltman
  • Samsung
  • Hisense
  • Ariston
  • Resideo
  • Braukmann
  • Daikin
  • Mitsubishi Electric
  • Danfoss
  • Soler & Palau
  • Toshiba
  • Hoval
  • Carrier
  • Vaillant
  • Grundfos
  • Viessmann

See all suppliers

Consultancy

Consultancy and energy efficiency

Energy efficiency in buildings

Smart solutions for building automation

Nothing evolves faster or less predictably than information technology. What is cutting edge today will likely be replaced tomorrow by a new standard. Add to this a multitude of different closed systems, and the result is that building automation uses many different communication systems.

We provide

  • Energy consumption analysis
  • Energy audit
  • Energy management
  • Project design and implementation
  • Technical and financial solution proposal
  • Replacement of old equipment with low energy consumption equipment
  • DANFOSS frequency converter solutions for existing equipment
  • Operation and maintenance support
  • Monitoring and evaluation of savings

Service and maintenance

Corrective and preventive technical service and maintenance

We do not only carry out preventive maintenance, we have qualified personnel who also ensure the implementation of corrective actions related to identified non-conformities.

Boiler technical maintenance

01

Boiler technical maintenance

Operations included in an overhaul:

  • Viessmann
  • Vaillant
  • Ariston
  • Checking boiler operation within the correct parameters, according to the technical data sheet
  • Checking boiler tightness
  • Checking thermo-manometers
  • Checking and cleaning the burner
  • Checking burner settings with a flue gas analyser, readjusting settings and checking wear of burners and their components
  • Cleaning and adjusting the combustion head assembly
  • Checking correct operation of the equipment controls, including adjustments and parameter changes at the client's request
  • Checking the water softening station: operation, settings, connection
  • Checking circulation pumps and motorised valves
  • Checking the supply voltage (supply voltage of the controls)
  • Checking chimney draught
  • Checking the gas stabiliser filter, if required
  • Checking emission levels and issuing reports, completing the required documents
  • Checking expansion vessel pressure
  • Burner adjustment
  • Adjusting and calibrating safety valves
Air conditioning service

02

Service and maintenance of air conditioning equipment

  • SPLIT
  • MULTISPLIT
  • COMMERCIAL
  • VRV
  • CHILLER cooling units

Carried out by AGFR certified personnel

Operations included in a chiller / VRV overhaul:

  • Toshiba
  • Mitsubishi Electric
  • Carrier
  • Diagnostics, fault history reading, manufacturer software
  • Checking the strainer
  • Checking hydraulic connections for leaks (water)
  • Checking hydraulic connections for leaks (refrigerant)
  • Checking water pressure
  • Checking refrigerant pressure
  • Checking electrical connections
  • Checking electrical components in the power panel
  • Measuring and recording starting currents
  • Measuring and recording rated currents in normal operation
  • Checking controller settings
  • Checking the electronic board
  • Checking and cleaning the heat exchanger coil (refrigerant)
  • Checking the refrigerant filter
  • Checking flow and return temperature sensors and frost protection
  • Checking and cleaning the coolant pump
  • Exterior cleaning of the chilled water buffer tank
  • Exterior cleaning of the expansion vessel
  • Checking and cleaning the water pressure gauge
  • Checking and cleaning the fan
  • Checking and measuring the compressor operating temperature
  • Checking and cleaning the refrigerant-water plate heat exchanger
  • Checking for moisture in the refrigerant circuit
  • Checking the flow switch (heat transfer fluid circulation)
  • Oil analysis
  • Exterior cleaning
Pumping system service

03

Service and maintenance of water pumping systems

Improve user comfort and reduce life cycle costs with smart pumps that integrate easily into your air-based or hydronic cooling system.

The overhaul includes at least the following operations:

We supply Wilo and Grundfos spare parts and remedy the non-conformities identified during overhauls.

  • Wilo
  • Grundfos
  • Checking the absorbed current and supply voltage
  • Visual check for fluid leaks at the mechanical seal, where applicable, to detect any leaks and replace the seal in time, preventing wear and corrosion of the supporting parts
  • Checking the isolation valves on pump suction and discharge
  • Checking the control panel
  • Checking bearing condition with a VIBROTEST device; the measurements are recorded in the intervention report
  • Alignment check for NL/NP pumps with a LASER device, with an analysis report issued
  • Checking the direction of rotation of each three-phase motor
  • Checking electrical connections for corrosion or mechanical damage
  • Checking and restoring expansion vessel pressure (working pressures up to 25 bar)
  • Sanitising buffer tanks for drinking water, grey water and rainwater tanks with approved solutions, in line with legislation
SILSI

Fire safety

SILSI

Inspection of fire suppression and extinguishing systems and installations

Technical service required by law

The maintenance service for fire suppression and extinguishing systems and installations (SILSI) consists of periodic preventive and corrective maintenance of these systems and is carried out by an authorised ARTBuilding technician with specific competence in this field.

This service covers inspection, maintenance, repair and testing of the components of water-based extinguishing installations: pressure gauges, visual and audible alarm devices, internal and external hydrants, pipes, fittings, connections, valves, tanks, pumps, fire water reservoirs, and control and signalling equipment (ACS).

Inspection, maintenance and overhaul operations are set out in the legislation by type of operation and frequency, and are recorded in the logbook for the operation, inspection and maintenance of the extinguishing installation.

Interior fit-out and design

Fit-out

Interior fit-out and design

An interior design project includes: measuring the space, defining the desired concept and visual identity, the furnishing plan, technical drawings (building services, electrical, ceilings), execution details for finishes and furniture, photorealistic renderings, a quote for the materials included in the project within the budget you set, and site supervision. We recommend this service when you need an in-depth design or redesign of your space.

For your project, we assign a professional team of architects and interior designers.

Flooring

Epoxy flooring works

Epoxy floors have become very popular recently because of their many advantages: they are dust-free, anti-static and anti-slip, and resistant to acids, corrosion and heavy traffic.

Epoxy flooring

Epoxy flooring is a continuous, seamless surface made of solvent-free coloured epoxy resins, with many fields of use.

Concrete and cementitious polyurethane screed

Polyurethane cement screed (or polyurethane cement concrete) is a modified, coloured, three-component, water-based, resin-rich polyurethane cementitious mix, smooth or textured, with high strength, suitable for floors subject to heavy loads, abrasion and chemical exposure.

Polyurethane floors

Polyurethane flooring is an attractive and durable floor that can be installed on dynamic substrates such as raised or suspended floors or old screeds, without joints, and is made of solvent-free coloured polyurethane resins, with many fields of use.

Rapid curing floor systems

The rapid curing floor is a multi-layer, three-component system based on reactive, fast-curing acrylic resins.

Parking

Floor systems for car parks also deserve attention, because parking has become a vital part of the community and is in constant use.

Road markings and pictograms

We have extensive experience in designing and applying epoxy paint road markings and pictograms to our clients' requirements.

Polished concrete

Substrate preparation

09

On-site safety valve calibration

We check and set the opening pressure of your safety valves on site, with a mobile test stand, so the installation is back in operation the same day.

  • Mandatory periodic inspection under ISCIR technical regulations
  • Inspection, cleaning, tightness check, setting to the design pressure and sealing
  • Valves for hot water and steam boilers, compressed air, refrigeration systems and boilers
  • Inspection and calibration report with the measured values for every valve

New business line

Equipment distribution

Alongside our services, we are developing the distribution of HVAC, heating, ventilation and pumping equipment to commercial partners. If you represent a shop, an installer or a regional retailer, let's build a sales channel together, backed by real technical support.

Technical blog

New articles, written by our service team

All blog articles

Let's work together

Need service or a quote?

We respond with a technical assessment, not a template.

en_USEN